Megalink logo
 
Set language to English Set språk til Norsk

Frequently asked questions

See also our YouTube Channel.

Target
  • How to set ID on target lift
  • ID on the target lift is set using jumpers on the target lift card. See the document ML2000Man02EN-Installation for more information.

    Edited: 2018-10-05  Link: https://www.megalink.no/login/?page=faq&lang=en#how-to-set-id-on-target-lift
  • Band advance length is zero
  • Somethimes an error in the system sets the motor length for the band advance to zero. To avoid this we recommend to power on the targets first, then power on the monitors.

    Edited: 2017-06-26  Link: https://www.megalink.no/login/?page=faq&lang=en#band-advance-length-is-zero
  • How to get maintenance warning after X shots on target
  • In MLRange goto Menu -> Setup -> Targets. 

    Edited: 2019-01-11  Link: https://www.megalink.no/login/?page=faq&lang=en#how-to-get-maintenance-warning-after-x-shots-on-target
  • How to calibrate my high power targets?
  • NB: Use Chrome, certain browsers give wrong values. Does not work with CU 18.37/18.38, use CU 18.19. 

    If the X and Y value of the monitor and the target is not consistent, the target can be calibrated.

    This can be done by moving the logical center on the target (Offset).

    Use this tool for finding the correct offset:

    https://www.megalink.no/login/?page=calibrate

    Edited: 2019-04-05  Link: https://www.megalink.no/login/?page=faq&lang=en#how-to-calibrate-my-high-power-targets
  • Troubleshoot 3D-Score 25/50 directly using monitor
  • A monitor can be connected directly to the 3D-Score 25/50 connection bar for troubleshooting. Only the lastest version of color monitor can be used. Version can be checked on the monitor Systemstatus -> Hardware: DU3 i1.

    Edited: 2019-02-06  Link: https://www.megalink.no/login/?page=faq&lang=en#troubleshoot-3d-score-2550-directly-using-monitor
  • LED indicator on controller unit (CU3) HW version: 64 to newest
  • During normal operation a green diode blinks with a period of a couple of seconds. If the diode blinks rapidly this may indicate too low voltage.

    During activity on the communication line a red/orange diode blinks. The frequency is affected by the number of units communicating on the same communcation line.

    Two green diodes blink whenever the microphone has detected a sound. One with a short blink and one with a longer blink. (Diodes may be red/orange)

    Edited: 2019-02-15  Link: https://www.megalink.no/login/?page=faq&lang=en#led-indicator-on-controller-unit-cu3-hw-version-64-to-newest
  • Where are the censors located?
  • Seen up front:

    3UXXX

     

        A    B    C

     

    4KXXX

     

        B    D

     

        A    C

     

    8K000

     

        B    B2    D

     

        A2        D2

     

        A    C2    C

     

    BIA1200:

        

        U1    U2    U3    U4        D1    B1    D2    B2

                               =

        L1    L2    L3    L4        A1    C1    A2    C2

     

    BIA1200_12

     

        U1    U2    U3    U4    U5    U6        B1    D1    B2    D2    B3    D3

                                            = 

        L1    L2    L3    L4    L5    L6        A1    C1    A2    C2    A3    C3

     

    Edited: 2021-03-08  Link: https://www.megalink.no/login/?page=faq&lang=en#where-are-the-censors-located
  • Check the IR diodes inside the 3D-Score
  • Shot detection in the 3D-Score depends on the IR-diodes and sensors inside the target.

    Use the camera on a cell phone to determine that there are IR-light in all the slots inside the target. Please note that only half of the slots contains IR-diodes with light visible on the camera. The other slots contains IR-sensors with no ligth. 

    On the small 3D-Score you will need to enable the IR-diodes:

    1. Unplug the power
    2. Press and hold the button on the rear side of the target while reconnection the power

    Edited: 2022-02-02  Link: https://www.megalink.no/login/?page=faq&lang=en#check-the-ir-diodes-inside-the-3d-score
    Range / Monitors
  • Factory reset / recovery monitor
  • Procedure for factory reset / recovery is changed. Please see the document ML2000 Manual – Display Unit (Monitor)  for more information.

    Edited: 2016-03-07  Link: https://www.megalink.no/login/?page=faq&lang=en#factory-reset--recovery-monitor
  • How do I change the language on the monitor?
  • Select Menu → Display Config → Language

    or

    Select Meny → Skjerm innstill → Språk

    Edited: 2016-09-12  Link: https://www.megalink.no/login/?page=faq&lang=en#how-do-i-change-the-language-on-the-monitor
  • What is the green/red circle plotted on the shots?
  • When the gauge is to small to be visible, an additional colored circle is added to the plot. Se explanation here: Plotting of shots

     

    Edited: 2017-10-17  Link: https://www.megalink.no/login/?page=faq&lang=en#what-is-the-greenred-circle-plotted-on-the-shots
  • How to remake the SD card on the Megalink second monitor kit
  • What is the blinking LEDs on the USB adapter
  • LED marked USB: The LED is blinking each 5 secound and for each message when connection to MLRange. The connection can be testet by sending a message from MLRange or fetch status.

    LED marked LINE/PWR: Lights when the adapter is powered. The LED is blinking when the adapter communicate with monitors/targets.

    Edited: 2018-02-05  Link: https://www.megalink.no/login/?page=faq&lang=en#what-is-the-blinking-leds-on-the-usb-adapter
    MLView
  • How to replace the logo with banner images?
  • The Megalink logo can be replaced by one or more banner images.

     

    The images can be placed in the BannerImages folder, a subfolder of the C:MegalinkView folder. The images must be of BMP format and have a size of 500x100 pixels. The files must have the following naming: image1.bmp, image2.bmp, etc.

    Edited: 2018-10-05  Link: https://www.megalink.no/login/?page=faq&lang=en#how-to-replace-the-logo-with-banner-images
    MLLive
  • MLRange do not connect to the MLLive application
  • If MLRange do not automaticly connect to the MLLive application you can force MLRange to use the IP address of the MLLive PC.

    • Close MLRange
    • Open the file C:Megalink angeMLRange.ini
    • Make a new line bellow the [CONFIG] section:
    • MLLiveIP=xxx.xxx.xxx.xxx

    Example:

    [CONFIG]
    MLLiveIP=192.168.128.43

    NB: Make sure there are no on the start of the line.

    Edited: 2022-06-16  Link: https://www.megalink.no/login/?page=faq&lang=en#mlrange-do-not-connect-to-the-mllive-application
  • How do I use MLLive?
  • What targets are supported by MLLive?
  • How much data is uploaded with MLLive
  • An event with 10 relays, 10 targets and an average of 35 shots per shooter gives an upload of approximately 40 MB.

    Edited: 2016-10-11  Link: https://www.megalink.no/login/?page=faq&lang=en#how-much-data-is-uploaded-with-mllive
  • What are the requirements for running MLLive
  • MLLive must be installed on Windows 7 or newer.

    Edited: 2016-12-02  Link: https://www.megalink.no/login/?page=faq&lang=en#what-are-the-requirements-for-running-mllive
  • Make an url to selected targets in MLLive
  • Here is how to make an url to selected targets instead of the complete range in MLLive:

    1. Go to resultat.megalink.no

    2. Select one ore more targets in the same range. The url will be results.megalink.no/#!/event_name/100m/

    3. To allways show for instance target 3, 4 and 8 every time you can change the url as follows: results.megalink.no/#!/event_name/100m/100m_3,100m_4,100m_8

    4. Save the url as a bookmark.

    Edited: 2018-10-05  Link: https://www.megalink.no/login/?page=faq&lang=en#make-an-url-to-selected-targets-in-mllive
  • Names are not showing or unreadable on iPhone
  • 1. Goto Settings --> Safari --> Clear History and Website data.

    2. Reload results.megalink.no

    Edited: 2018-01-30  Link: https://www.megalink.no/login/?page=faq&lang=en#names-are-not-showing-or-unreadable-on-iphone
  • Browser: Targets not loading, only a spinning wheel
  • MLLiveArena
  • What is MLLiveArena
  • MLLiveArena is a new and more simple system for audience display. MLLiveArena is working like the MLLive App, but with local storage. Internett is not required. 

     

     

    Edited: 2022-05-12  Link: https://www.megalink.no/login/?page=faq&lang=en#what-is-mllivearena
  • MLRange do not connect to the MLLiveArena application
  • If MLRange do not automaticly connect to the MLLiveArena application you can force MLRange to use the IP address of the MLLiveArena PC.

    • Close MLRange
    • Open the file C:\Megalink\Range\MLRange.ini
    • Add a new config named [LiveArena]
    • Make a new line bellow the [LiveArena] section:
    • ip=xxx.xxx.xxx.xxx

    Example:

    [LiveArena]
    ip=192.168.128.43

    Edited: 2022-09-19  Link: https://www.megalink.no/login/?page=faq&lang=en#mlrange-do-not-connect-to-the-mllivearena-application
  • What target fronts are supported in MLLiveArena
  • MLShoot
  • How do I activate ballistic test (ammo test)?
  • To move the average to center press [F12] or select "Ballistic test mode" in the "Ballistic test" menu. 

    To make a report press [Ctrl] + [P] or select Menu → Print.

    It's recommended to use the course of fire "Testing". To show a cross instead of a target select the target named "International Ballistic test".

     

    Tip: In the meny Ballistic test → Ballistic test config the options Name cards and Name series should be selected.

    To make MLShoot allways start in ballistic test mode select BTS mode on startup in the config menu.

    (Works on MLShoot v.17.42 or newer)
    Edited: 2017-09-28  Link: https://www.megalink.no/login/?page=faq&lang=en#how-do-i-activate-ballistic-test-ammo-test
  • How do I remove shoots from the list?
  • To remove a shot press [F9] to get the shot details list. Activate or deactivate each shot by cliking on them.

    Edited: 2016-09-05  Link: https://www.megalink.no/login/?page=faq&lang=en#how-do-i-remove-shoots-from-the-list
  • How do I change the language on MLShoot?
  • Select Menu → Display Config → Language

    or

    Select Meny → Skjerm innstill → Språk

    Edited: 2016-09-05  Link: https://www.megalink.no/login/?page=faq&lang=en#how-do-i-change-the-language-on-mlshoot
  • Message "HASP Error" and no shots are ploted
  • The problem is that the driver for the HASP dongle is not corectly installed. 

    - Check first that the dongle is connected to the computer. 

    To solve the problem try the following:

    1. Remove the HASP driver in the Device manager (if you find it there)
    2. Unplug the HASP dongle
    3. Reboot the computer
    4. Install MLShoot
    5. Insert the HASP dongle and start MLShoot

    Edited: 2021-02-24  Link: https://www.megalink.no/login/?page=faq&lang=en#message-%26quot%3Bhasp-error%26quot%3B-and-no-shots-are-ploted
    Biathlon
  • Software working slowly
  • When the event database grows, the software can start to respond slowly. It’s therefore recommended to clean the database before new events.

    Do the following:

    • Make sure MLBiaWeb is not running.
    • Start MLBia.
    • Press the setup icon: 
    • Then press the “Clean Database” button: 

    NB: This will delete all old events. But the old database is backup-ed to the folder MLBiaDbackup.

    Edited: 2016-03-08  Link: https://www.megalink.no/login/?page=faq&lang=en#software-working-slowly
    Other
    © Megalink 2016 - 2023
    We're using cookies [Read more]